Newsletter

Cart

Partners

Business Hours

  • Monday 9am to 5pm
  • Tuesday 9am to 5pm
  • Wednesday 9am to 5pm
  • Thursday 9am to 5pm
  • Friday 9am to 3pm

Limb Driver Setup Instructions

Limb Driver Pro Setup

1. Attach rest to the riser with bolt provided.LDProLegend
2. To adjust the center shot, loosen windage bolt and slide rest left or right to desired location and tighten windage bolt.
3. To adjust launcher blade height, loosen elevation bolt and slide rest up or down to desired location and tighten elevation bolt.
4. To adjust spring tension, loosen allen screw on spring retainer and turn upwards for more tension and downwards for less tension. You want just enough tension to raise the launcher blade while fully supporting the arrow.
5. Choose top or bottom limb to attach the limb driver cord in order to avoid interference with other accessories.
6. Prepare limb surface by cleaning with denatured alcohol. Remove paper backing and adhere pad to clean limb surface.
7. Tie limb driver cord around the limb over the pad using a half hitch knot.
8. If the cord is attached to the top limb, run the cord through the top limb cord hole on the stopper. Bottom limb cord hole for the bottom limb. Keep tension on cord while pushing launcher arm down toward the shelf and tighten cord set screw to hold cord and rest in place. Tighten mounting bracket set screw.
9. Draw bow back and make sure launcher blade rises as cord goes slack. Let bow down and make sure launcher blade lowers as cord is again pulled taught. Do this with an arrow on the string in case of misfire to prevent dry fire.

Limb Driver Pro-V Setup

1. Attach rest to the riser with bolt provided.LDProVLegend 2. To adjust the center shot, loosen windage bolt and slide rest left or right to desired location and tighten screw.
3. To adjust launcher arm height, loosen elevation bolt and slide rest up or down to desired location and tighten bolt.
4. To adjust spring tension, loosen allen screw on spring retainer and turn clockwise for more tension and counter clockwise for less tension. You want just enough tension to raise the launcher arm while fully supporting the arrow. This applies to the Right handed rest. *Reverse instructions for Left handed rest.
5. Prepare top limb surface by cleaning with denatured alcohol.
6. Remove paper backing and adhere pad to clean limb surface.
7. Tie limb driver cord around the limb over the pad using a half hitch knot.
8. Run cord down through cord hole in stopper. Keep downward tension on cord while pushing launcher arm down toward the shelf and tighten cord set screw to hold cord and rest in place. Tighten mounting bracket set screw.
9. Draw bow back and make sure launcher arm rises as cord goes slack. Let bow down and make sure launcher arm lowers as cord is again pulled taught. Do this with an arrow on the string in case of misfire to prevent dry fire.
10. Prepare inside surface of the containment cage by cleaning with denatured alcohol. Apply moleskin to inside surface where needed.

Limb Driver Micro-Elite Setup

 

 

1. Attach rest to the riser with bolt provided.LDMELegend
2. To adjust the center shot, loosen windage bolt and adjust the rest left or right using the windage micro-adjust knob to desired location and tighten windage bolt.
3. To adjust launcher arm height, loosen elevation bolt and adjust rest up or down using the elevation micro-adjust knob to desired location and tighten elevation bolt.
4. To adjust spring tension, loosen allen screw on spring retainer and turn clockwise for more tension and counter clockwise for less tension. You want just enough tension to raise the launcher arm while fully supporting the arrow. This applies to the Right handed rest. *Reverse instructions for Left handed rest.
5. Choose top or bottom limb to attach the limb driver cord in order to avoid interference with other accessories.
6. Prepare limb surface by cleaning with denatured alcohol. Remove paper backing and adhere pad to clean limb surface.
7. Tie limb driver cord around the limb over the pad using a half hitch knot.
8. If the cord is attached to the top limb, run the cord through the top limb cord hole on the stopper. Bottom limb cord hole for the bottom limb. Keep tension on cord while pushing launcher arm down toward the shelf and tighten cord set screw to hold cord and rest in place. Tighten mounting bracket set screw.
9. Draw bow back and make sure launcher blade rises as cord goes slack. Let bow down and make sure launcher blade lowers as cord is again pulled taught. Do this with an arrow on the string in case of misfire to prevent dry fire.

Blade X Setup